DigiPlus

List of the catalogue of this article:

• 1, What is the name of the door handle?
• 2, The door lock can't bounce back, how to solve it
• 3, The door lock does not bounce back, the door cannot be closed
• 4, The door lock is pressed down and the door can't be closed
• 5, co-driver's hand buckle How to fix a broken door

What is the name of the door handle?

1. According to the query Baidu Encyclopedia, the handle of the car door is called the door lock. It is also called the door button.

2. The place where the door is opened is called the handlebar. The parts of the door are as follows: from top to bottom: left front door glass, left front reflector, left front glass seal, outer trim strip, left front door trim strip.

3. The handle inside the door refers to an opening device installed inside the car door. It usually consists of a handle and a lock cylinder, which is responsible for opening and closing the door. The inner handle of the door provides convenience for passengers to get in and out of the car.

How to solve the problem if the door lock buckle doesn't bounce back

1. Then check whether the door lock block is stuck. In this case, you need to remove the door lock block, specifically check whether it is rusty and stuck, and do the lubrication treatment again. If there is still a similar fault, you need to replace the new central control lock block to solve the problem.

2. The driver can clean the lock hook with rust remover, and then apply butter evenly on the lock hook, so that the latch of the door lock can bounce back normally. If the problem that the pin of the door lock does not rebound has not been solved, it may be that the lock hook of the door lock is tilted.

3. Loosen the silk buckle. Use a flat-mouthed tap into the flat groove and knock it with a hammer. This is to loosen the silk buckle.

4. If the door buckle does not bounce back, it may be a deviation in the position of the buckle. It is necessary to adjust the position relationship between the snap and the snap ring;You can use tools such as a screwdriver to gently snap the buckle, and then close the door for debugging until it is suitable. Rust on the lock hook will also cause the door buckle to not bounce back.

The door lock buckle does not bounce back, and the door can't close

1. The door lock buckle does not bounce back. The reason why the door can't be closed is that the position of the buckle is deviated, and the position relationship between the snap and the buckle ring needs to be adjusted; the lock is rusty, resulting in the door The snap doesn't bounce back. If the door buckle does not bounce back, there may be a deviation in the position of the buckle.

2. The reason why the door lock buckle does not rebound and the door cannot be closed: there is a deviation in the position of the buckle, and the position relationship between the buckle and the buckle ring needs to be adjusted; the lock hook is rusty, resulting in the door buckle not rebounding.

3、The DigiPluscar door lock can't close the door if it doesn't bounce back. It is likely that the lubricant inside the door lock is insufficient, so this situation occurs. The owner only needs to add an appropriate amount of lubricating oil into the door lock to solve the problem.

The door lock is pressed down and the door can't be closed

1. The solution is to remove the screw on the door lock and you can see the lock; put the position of the lock inward or outward slightly Make a slight adjustment; make sure that you don't need to close it hard when locking the door firmly.

2. The reasons are: the hinge of the door or the door lock card is shifted, the door lock tongue cannot be reversed and stuck, the contact switch problem of the door lock is closed, and the height of the contact installation is insufficient, so that although the door is closed in place, the door warning light will still be on.

3. It can only be repaired by disassembling the vehicle door panel. If it is damaged, it needs to be replaced directly. If it is stuck due to mechanical failure, it needs to add lubricating oil and then restore it to its original state. Only in this way can it be used normally, otherwise the vehicle door cannot be closed.

4. Maintenance can only be carried out by removing the vehicle door panel. If it is damaged, it needs to be replaced directly. If the mechanical failure is stuck, you need to add lubricating oil and then restore it to its original state. Only in this way can it be used normally, otherwise the door cannot be closed. Can the central control lock be closed if the door lock is damaged? In this case, the central control lock cannot be closed.

5. If the click sound is not flexible or there is a friction sound, it means that the lock is aging or lacks lubricating oil. In this case, the lock needs to be replaced or the lubricant needs to be added;When the door is opened and closed, the door lock motor buckle is displaced, resulting in the inability to close the door. In this case, you need to go to the repair shop to adjust the position of the lock buckle.

6. If the door lock is accidentally pressed in, causing the door to not be closed, the owner does not need to worry too much. The car owner needs to unlock the door first, then find the car key and insert it into the lock, and gently pull the door handle. At this time, the lock can be opened.

How to repair the broken door of the co-driver's hand buckle

If you are sure that the lock is good, the problem may be that the lock has been opened, or maybe the hand buckle can't pull the opening mechanism of the trunk lid, the structure is not in place, or the lock is bitten by the lock buckle, pull the buckle Lift the trunk up hard to see if it is possible to separate the lock from the buckle and open the trunk, (if the buckle is broken, you can only replace it).

If it's a mechanical machine, it's good to change one. If it's a motor, check it first to see if the motor needs to be replaced. Some storage boxes are mainly mechanical and easy to break down. You can take a look at this one.

Disassemble the door handle of the car and check whether the hinge or wrench inside the door handle is normal. If there is any deformation, it needs to be clamped with a tool to correct it; if it cannot be repaired by yourself, it is recommended to send the door handle of the car to a professional repair shop for maintenance.

Once an installation error occurs, the door will not be able to open again after it is closed. It will bring some trouble to the later maintenance. If the vehicle door is damaged, it must be repaired by a professional repair factory, which is the safest way.

Repair method for broken car door handles: firstRemove the interior door panel and interior panel of the vehicle, and then check whether the parts inside are stuck. If they are stuck, you can add some lubricating oil to lubricate the parts. If it is not a stuck problem, it is better to replace a new handle and install it back.