Casino Plus app

List of the catalogue of this article:

• 1,What to do with the outer plate of the rear cover of the car
• 2 , Car headlight rear cover extension
• 3、BYD QinHow to open the front seat and Casino Plus apprear cover
• 4, What is the reason for the damage to the automatic opening function of the rear cover of the suv car?
• 5, The rear of the carWhere is the plate

What to do if the outer plate of the rear cover of the car is contaminated

1. Usually, park the car in a shadow area, avoid direct sunlight, and choose a time when the temperature is relatively mild during the day. Wash the vehicle. 2. The dust in some places is not easy to see. You can use plastic bags to detect pollutants. First of all, you need to rub the plastic bag to generate static electricity to adsorb dust.

2. Slot and firewall sound insulation treatment, these two parts can be regarded as auxiliary soundproofing treatment. Through the treatment of these two parts, the effect is also better. However, the firewall soundproofing needs to be removed from the console for better soundproof installation, so this part must be soundproofed, and we need to pay special attention to it.

3. Remove the car carpet. If the diesel pollution is serious, you should consider whether to replace it, because there may be no way to remove the smell of diesel in a short time. It is recommended to go to the 4S store or car beauty shop for a comprehensive cleaning. You can put some bamboo charcoal bags in the car, which can play a certain role in deodorizing and purifying the air.

Car headlight back cover extension

1. First, use a heating gun to slowly walk through the glue on both sides of the lampshade, which will melt again. At this time, just close the lid and apply a layer of sealant for double protection. I usually use transparent heat-resistant silicone, which is waterproof and sunscreen, and has toughness. There are many kinds of glue. If you are not sure, ask the people in the garage.

2. The headlights of the car are responsible for the lighting and safety of driving at night. The importance is self-evident, which is equivalent to human eyes. However, human eyes often do eye care exercises, and for car headlights, eye care exercises are also needed.

3. But this kind of renovation is very particular about technique and easy to "relapse". Polished renovation: This method is relatively common, and ordinary car beauty shops can do it.In fact, the principle is like the body paint, sanding the headlights with sandpaper, and then polishing with special wax.

How to open the rear cover of the BYD Qin front seat

There are 4 14 screws under the seat. Unplug the plug below to take out the seat.

How to remove the seat of BYD Qin co-driver: There are 4 14 screws under the seat. Unplug the plug below to take out the seat. BYD Qin is a high-performance sedan of the second-generation DM (switching between pure electric and hybrid modes) independently developed by BYD Co., Ltd.

Because of the battery, the rear seat of Qin Plus is relatively short, and the rear space is also relatively low.When the rear seat is opened, you only need to pull the pull rod under the seat by hand and push the seat forward. There is a snap on the front left and right of the seat, just open it.

Push the latch up until the front compartment lid is released, and then lift the front compartment lid. Lift the front hatch up, and the support rod will automatically support the front hatch. Close the hatch cover. Press the front hatch hard, and the front hatch will close automatically when it falls. After closing the front hatch, check whether the lock is locked.

What is the reason for the damage to the automatic opening function of the rear cover of the suv car?

It may be a problem with the connecting rod or lock cylinder, or a problem with the body part. You can try to put down the back seat, enter the trunk from the emergency exit, and open the lock lever directly to unlock it manually.If there is a problem with the connecting rod or lock cylinder, usually the lock cylinder is dirty or rusty, you can spray rust remover into the lock cylinder several times and try to open it.

Hello, the trunk of the Audi a6 pops up automatically for no reason. This situation may be due to damage to the switch of the trunk. In other words, if there is a problem with the control unit of the system, it will cause this situation. I hope my answer can help you! Have a good time using the car! [ For car questions, ask the car master. 4S store professional technician, 10 minutes to solve.

The reasons why the car cannot start are the battery is too low, the starting motor is damaged, the ignition system fails, the fuel supply system fails, the engine mechanical system fails, etc. When the low temperature in winter and the failure of individual electrical equipment are turned off, the vehicle will not be able to start, especially for long-term short-distance low-speed use in winter, and the battery voltage will be lower than the rated value.

Where is the rear enclosure of the car

The rear enclosure of the car is below the trunk of the car. Usually, the rear enclosure plate and the frame of the car are not integrated, but welded. If the rear enclosure plate is cut and replaced, it is an accident car. If it's just a knock, pull the table frame and repair that does not use cutting and welding, it is not considered an accident car.

The rear panel of the car is the rear panel of the trunk. That is, the circle under the trunk. Generally speaking, the rear enclosure plate and frame of the original factory are not integrated, but welded. The rear enclosure belongs to the body cover, and there will not be much depreciation after replacement. The rear enclosure is composed of several pieces, not a whole.

The rear panel of the car is located under the trunk of the car and is installed around the bottom of the trunk.Generally, the rear wall of the vehicle is not integrated with the frame, but belongs to welding. If the rear wall panel has been cut and replaced, it is an accident car. In fact, it is not easy to replace the backboard. It takes a long time to drill the back plate welds one by one, and welding and glueing are very troublesome.